Two Ram Baler Model TR-1388-200

       Revised: 6/06

HYDRAULIC

         Main Pumps                                  596 GPM Total Flow (Regen. System)

            System Pressure                     3200 PSI

            Main Cylinder                          13 In Bore

            Ejector Cylinder                  9 In Bore

            Bale Door Cylinder             8 In Bore

            Precompression Cyl.           8 In Bore (Optional)

            Total Force                               424,530 Lb

            Ram Face Pressure                253 PSI

            Oil Reservoir                           1500 Gallon Capacity

                                                                        L&P Wire-Tie or Accent Wire- Tire

ELECTRICAL

            Main Motor                                Two (2) 100 HP, 460 Volt, 3 Phase, TEFC, Special Duty, Wye Delta Starting

            Cooler Pump Motor              7.5 HP, 460 Volt, 3 Phase

            Cooler Fan Motor                 Two (2) 3 HP, 460 Volt, 3 Phase

            Strapper Pump Motor          10 HP, 460 Volt, 3 Phase

            Controls                                     Programmable Controller with Diagnostics and Phone Modem

            Photocell                                   Infrared Type

STRUCTURAL

         Length Overall                      36 Ft

            Hopper Opening                        96 In Long x 72 In Wide (W/Lid 90 In Long x 60 In Wide)

            Charge Box Opening             96 In Long X 57.5 In Wide (W/Lid 90 In Long x 57.5 In Wide)

            Width Overall                         21 Ft 0 In

            Charging Hopper Ht.            7 Ft 6 In (With Lid 13 Ft 1 In)

            Shear Blade                               Knife Steel, Reversible

            Liners                                             Hardox 400 or Equal  (Charging Box totally lined w/wear plates)

            Shipping Weight                       53 Tons Approximate (With Lid 57 Tons)

PERFORMANCE

            Bale Size                                       45 In Wide x 30 In High x 62-64 In Length

            Bale Volume                              50 Cubic Feet Expanded (Approximate)

            Cycle Time                                  9 Seconds (No Load – Main Cylinder Only)

            Bale Time                                     72 Seconds (Strapper Time Included)

                                                                        *(3 Strokes/Bale) Estimated for OCC W/Lid

Material	Material PCF Infeed Density	Bale Weight LB	Density  PCF Baled	Output No Lid Tons per Hr	Output With Lid Tons per Hr
*OCC	2.5 -  4	up to 1500	up to 30	up to 24	up  to 24
*News	6 - 8	up to 1700	up to 34	up to 40	up to 40
*PET	.75 - 4	up to 1250	up to 25	up to 9	up to 10
*UBC	1.5 - 4	up to 1200	up to 24	up to 16	up to 18
*Solid Waste	8 - 12	up to 2500	up to 50	up to 44	up to 46
*Carpet Waste	2.5 -  4	Up to 1500	Up to 30	Up to 18	up to 18

*Performance Rates, Bale Weights, and Bale Densities Are Subject to Moisture Content, Material Pre-Bale Densities,

Feed Rates, And Other Variables in Baling

 

STANDARD FEATURES                                          AVAILABLE OPTIONS

Programmable Controller with Phone Modem                  Pre Compression Lid

Oil Cooler and Oil Heater                                                  Conveyor Controls

Bale Door / Relief                                                                      Feed Hopper Extension with Upper Level Sensor

Wye-Delta Starting                                                                 Contact Factory for other Options

Hydraulic Pumps Submerged in Oil to Eliminate Cavitation

 

Specifications and Design are Subject to Change if, in the opinion of the Manufacturer, the Change is an improvement.